Key takeaways
- A 100-125 amp single-phase sub panel suits a detached garage, workshop, or small addition needing several circuits for lighting, outlets, and a tool or two, a 60-100 amp panel suits a smaller outbuilding or a single-purpose space like a well…
A 100-125 amp single-phase sub panel suits a detached garage, workshop, or small addition needing several circuits for lighting, outlets, and a tool or two, a 60-100 amp panel suits a smaller outbuilding or a single-purpose space like a well pump house, and anything above 125 amp generally points toward a dedicated main panel conversation rather than a simple sub panel. Panel selection here is an electrical safety decision governed by code, not a style choice, so the final sizing and model should be confirmed with a licensed electrician against the specific feeder circuit and local code requirements.
What a Sub Panel Does and Why Amperage Isn’t the Only Spec
A sub panel, sometimes called a subpanel or secondary panel, distributes power to a group of circuits from a feeder that originates at the main service panel, commonly used to extend power to a garage, workshop, finished basement, or addition. Single-phase refers to the type of power most residential properties receive, as opposed to three-phase service more common in commercial or some larger residential setups. While amperage rating gets the most attention, the number of circuit spaces, the panel’s compatibility with the breaker brand already in use, and whether it’s rated for indoor or outdoor installation all matter just as much for a correct, code-compliant installation.
Amperage Rating and Feeder Wire Sizing
The sub panel’s amperage rating has to match what the feeder wire and breaker at the main panel can actually supply; installing a 125 amp sub panel fed by wire and a breaker sized for 60 amp does not give the panel 125 amp of usable capacity; it creates a mismatch that an electrician would correct during a proper installation. Brands such as Square D, Eaton, Siemens, and GE/ABB publish panels across the common 60, 100, and 125 amp range for residential sub panel use, each requiring feeder conductor sizing that follows the National Electrical Code or the applicable local code, which a licensed electrician calculates based on distance, load, and wire type.
Number of Circuit Spaces
Panels are sold by the number of circuit spaces or slots available, commonly in the 8, 12, 16, 20, 24, or 30-circuit range for sub panels, and this number should be sized with some spare capacity for future circuits rather than filled exactly to the planned load. A workshop or garage sub panel that seems adequately sized today can run out of room quickly once a few 240-volt tool circuits, a mini-split, and general lighting and outlet circuits are all accounted for.
Main Lug Only vs Main Breaker Panels
A main lug only (MLO) panel has no built-in disconnect and relies on a breaker at the originating panel to serve as the disconnect for the whole sub panel, while a main breaker panel includes its own disconnect at the sub panel location. Many jurisdictions require a local disconnect at or near a detached structure like a garage or workshop, which can make a main breaker panel the code-required choice for that specific application; this is a point to confirm with a licensed electrician familiar with local code rather than deciding from product specs alone.
Indoor vs Outdoor Rated Enclosures
Panels installed outdoors or in unheated, exposed locations need an enclosure rated for that environment, typically marked with a NEMA rating that indicates resistance to rain, dust, or other conditions, while standard indoor panels are not built for that exposure. Installing an indoor-rated panel in an outdoor or damp location is both a code violation in most jurisdictions and a genuine safety hazard, so the enclosure rating needs to match the actual installation environment.
Breaker Compatibility
Panels are generally designed to accept breakers from the same manufacturer or specific listed compatible brands, and using an unlisted or mismatched breaker in a panel is both a code issue and a safety risk since the panel’s bus bar and breaker interface are engineered together. Checking the panel’s documentation for its specific compatible breaker list before planning out circuits avoids ordering breakers that don’t fit or aren’t listed for that panel.
At a Glance: Sub Panel Types Compared
| Panel Type | Best For | Key Stated Specs | Limits |
|---|---|---|---|
| 60-100 amp main lug sub panel | Small outbuildings, single-purpose spaces | 8-16 circuit spaces typical; relies on main panel breaker as disconnect | No local disconnect; may not meet code for detached structures |
| 100-125 amp main breaker sub panel | Garages, workshops, additions needing multiple circuits | 16-24 circuit spaces typical; includes its own disconnect | Higher cost than main lug only equivalent |
| Outdoor NEMA-rated enclosure panel | Panels mounted outside or in exposed locations | NEMA 3R or similar weather-resistant rating per maker | Not interchangeable with indoor-rated enclosures |
| High circuit-count panel (24-30 spaces) | Larger workshops or multi-use outbuildings | Room for future circuit expansion | Larger physical footprint for mounting |
| Brand-matched panel to existing main panel | Simplifying breaker sourcing and future repairs | Compatible breaker line shared with the main panel brand | May limit choice if preferred brand isn’t locally stocked |
Pick This If…
| Your Situation | Recommended Type |
|---|---|
| You’re powering a detached garage or workshop with several tool circuits | 100-125 amp main breaker panel with 16-24 spaces |
| The sub panel will sit in a detached structure per local code | A main breaker panel with its own disconnect, confirmed against local code |
| The panel will be mounted outdoors or in a damp location | An enclosure with the NEMA weather rating the installation environment requires |
| You expect to add circuits later, like a mini-split or EV charger | A panel with extra circuit spaces beyond the current planned load |
| You already have a specific breaker brand in your main panel | A sub panel listed as compatible with that same breaker line |
Three Alternatives Worth Comparing
Upgrading the Main Service Panel Instead
For homes where the main panel is already near capacity, some electricians recommend upgrading the main service panel rather than adding a sub panel, particularly if multiple future additions are planned across the property. This is a larger scope of work and cost than a sub panel alone.
A Dedicated Circuit Instead of a Full Sub Panel
For a single high-draw appliance or tool rather than a whole structure needing multiple circuits, running one dedicated circuit from the main panel can be simpler and less costly than installing a full sub panel, though it doesn’t scale if more circuits are needed later.
Transfer Switch or Generator Interlock Panel
For buyers whose underlying goal is backup power rather than simply extending circuits to a new space, a transfer switch or interlock kit paired with a generator addresses a different need than a standard sub panel and is worth discussing separately with an electrician.
Frequently Asked Questions
Do I need a permit to install a sub panel?
Most jurisdictions require a permit and inspection for sub panel installation since it involves modifying the home’s electrical system, and requirements vary by location. Checking with the local building department before work begins, or having the hired electrician handle the permit, is the standard approach.
Can I install a sub panel myself?
While some jurisdictions technically allow homeowner electrical work with a permit, sub panel installation involves sizing feeder wire, confirming breaker compatibility, and often making decisions about grounding and bonding that carry real safety consequences if done incorrectly. A licensed electrician is the generally recommended choice for this type of installation.
What’s the difference between a sub panel and a main panel?
A main panel is where utility power first enters the home’s electrical system and includes the main service disconnect, while a sub panel is fed from the main panel’s breaker and distributes power further to a specific area like a garage or addition. Grounding and bonding requirements differ between the two and are a common point an electrician checks carefully during sub panel installation.
How far can a sub panel be from the main panel?
Distance affects feeder wire sizing because voltage drop increases over longer runs, so a sub panel farther from the main panel may need larger-gauge wire than the same amperage over a shorter run. An electrician calculates this based on the specific distance, load, and local code requirements rather than a fixed rule of thumb.
Does a detached garage sub panel need its own grounding rod?
Many codes require a separate grounding electrode, such as a ground rod, at a detached structure in addition to the grounding provided through the feeder from the main panel, though specific requirements vary by jurisdiction and panel configuration. This is a code detail an electrician confirms as part of the installation plan rather than something to assume either way.
What size breaker do I need at the main panel to feed a sub panel?
The breaker at the main panel needs to match the feeder wire’s rated ampacity and the sub panel’s intended capacity, and oversizing that breaker beyond what the feeder wire can safely carry creates a fire risk rather than simply adding headroom. This sizing calculation should be done by a licensed electrician based on the specific wire run and panel chosen.